ELECTRONICS AND NAVIGATION

NAVIGATION (FLYBRIDGE / UPPER HELM)

1. GPSMAP 8617, U.S and Canada G2 + LakeVu HD (2)
2. GMI 20 digital marine instrument display (2)
3. GHC™ 20 marine autopilot control unit
4. iCom HM195B VHF command mic IV (2)
5. AIS™ 800 Class B transceiver

NAVIGATION (PILOTHOUSE /LOWER HELM)

1. GPSMAP 8617, U.S and Canada G2 + LakeVu HD
2. GPSMAP 8622, U.S and Canada G2 + LakeVu HD (3)
3. GMI 20 digital marine instrument display (2)
4. GHC™ 20 marine autopilot control unit
5. Garmin USB card reader
6. GRID™ 20 Garmin remote input device
7. iCom M506 VHF radio with rear-mount mic (2)

NAVIGATION (MASTER STATEROOM AND CREW CAPTAIN STATEROOM)

1. GPSMAP® 742 plus (navigation PC integrated into Garmin screens for 2nd ECS unit. Nobeltec Time Zero with US East Coast and Bahamas chart system installed)

NAVIGATION (AFT DECK DOCKING)

1. GMI 20

AUTOPILOT

1. GHP Reactor, hydraulic with Smartpump V2 corepack, with GHC™ 20
2. GRF 10 rudder feedback sensor

ROOF AND RADAR ARCH

1. GMR™ 2526 xHD2 open array radar and pedestal (25kw/6-foot/96nm)
2. GMR Fantom™ 126 Solid-state open array and pedestal
3. 16' 10dB VHF antenna (2) and a 4' 4.5db AIS antenna 
4. 5"x8" 15-watt hailer horn (2)
5. gWind™ wired
6. GPS 19x NMEA 2000 (2)
7. GA™ 38 GPS/GLONASS antenna
8. GXM™ 54 SiriusXM® marine receiver

SOUNDER AND TRANSDUCER

1. GSD™ 25 Premium sonar module
2. AIRMAR 1kW B260, bronze, thru-hull, fairing, depth/temp
3. AIRMAR 1kW B265LH,12-pin thru-hull, CHIRP 42-65 kHz & 130-210 kHz

CAMERAS

1. Cameras (6) integrated into the Garmin network: 2 engine room cameras (fixed), 3 260-degree pan and tilt cameras for aft and side decks, and 1 FLIR camera on mast
2. Secondary Arlo Camera System available aboard for wireless security of the yacht

AUDIO VISUAL

The entertainment system aboard was recently updated to Roku TV (all TV's) through the Starlink on the yacht.

STARLINK

1. Starlink Maritime Mobile antenna

SATELLITE TV

1. 24" dome for DirecTV
2. 4 directional Wifi Antennas linked to the Pepwave internet wireless receiver in the salon
3. TracVision UHD7, standard size
4. 16-tuner SWM expander kit

SHIP-TO-SHORE TV

1. Ship-to-Shore TV socket

TVS AND BOSE ENTERTAINMENT SYSTEM

1. Teak-framed TVs in salon, master stateroom, VIP stateroom, port guest stateroom, starboard guest stateroom, port and starboard crew staterooms, crew galley and a portable TV (9 total)
2. Crew area TV has storage behind it
3. New 32" portable Samsung Smart TV, with stands on aft deck, flybridge and in pilothouse
4. Roku TV and accessories in salon
5. Denon entertainment system with surround sound speakers

FLYBRIDGE AND BOAT DECK

1. MS-NRX300, NMEA 2000 wired remote (2)
2. Apollo RA770 marine stereo
3. JLM6-770X-C-GwGw 7.7" marine coaxial speakers (3)

PILOTHOUSE

1. MS-NRX300, NMEA 2000 wired remote
2. Apollo RA770 marine stereo
3. Signature Series, 6.5" classic white speakers

SALON

1. MS-NRX300, NMEA 2000 wired remote
2. Signature Series, 6.5" classic white speakers
3. DIRECTV HR24 HD receiver box

FORE DECK

1. MS-NRX300, NMEA 2000 wired remote
2. JLM6-770X-C-GwGw 7.7" marine coaxial speakers

AFT DECK

1. MS-NRX300, NMEA 2000 wired remote
2. JLM6-770X-C-GwGw 7.7" marine coaxial speakers

MASTER STATEROOM

1. DIRECTV H25 HD receiver box
2. MS-NRX300, NMEA 2000 wired remote
3. Signature Series, 6.5" classic white speakers

VIP / PORT GUEST / STARBOARD GUEST / BOTH CREW / CREW GALLEY

1. DIRECTV H25 HD receiver box

OTHER ACCESSORIES

1. UPS, 120V 1.5kVA in the pilothouse and 900VA in the salon (for all H25)

Twin Northern Lights 38k (60hz) generators with sound shields (P: 1704 hrs, S: 1546 hrs - both units borescoped at the yard, had new injectors installed as well as all valve lashing adjusted. New oil pressure sensors installed)

WALKTHROUGH

The current owners of JULIANNE, who were previously owners of a 90’ Burger Motoryacht and a 81’ Northern Marine, along with the Outer Reef team consulted with the most experienced representative of Soundown Corporation to ensure their new 90’ Outer Reef Motoryacht would set the bar in terms of premium sound insulation. After a $130,000 investment these owners have ensured this technology has created the quietest, vibration-free engine room, in conjunction with the advanced enclosed shaft SeaTorque System. Additionally, throughout the entire yacht, there is no transmission of sound from showers running water, sinks, toilet flushings, or even door closings. During extensive sea trials post-installation, Outer Reef’s electronics technician, who is well-known within the industry and services many other new builds, found that while the yacht was at full load on the engines, and standing on the aft deck, JULIANNE surpassed any previous vessel in terms of her quietness in all circumstances and while underway.

JULIANNE is equipped with a large, comfortable aft deck table that has both perimeter and built in seating for eight, around a custom designed teak table for Alfresco dining. Stepping into the interior, the very spacious salon, galley, and main deck pilothouse connect within an inviting, spacious and bright living and entertainment space. An electrically operated, beautifully appointed rising wall can easily separate the pilothouse for privacy and night running. A main deck day head with outside access adds convenience to owners and guests as well. The two interior staircases, as well as the aft deck to boat deck staircase, have added steps for additional safety and conform more to home-style staircases.

Stairs starboard of the helm lead down to the owner and guest cabins, which offer more accommodation space than any previous Outer Reef built to date. The VIP cabin is forward with queen size berth and ensuite head. The port guest cabin has twin lower berths with ensuite head, and the starboard cabin has a queen berth with ensuite head. The Master is midship with a king berth, and a very large head with spacious storage and full-size laundry washer and dryer. The ensuite head has a separate toilet compartment. The hand selected custom furnishings, natural stone choices, and Silestone counters provide a warm, comfortable and rich environment throughout the yacht.

An aft staircase in the salon leads to the largest crew quarters ever provided on an Outer Reef. Finished to the same level as the rest of the yacht, this area is furnished with a full galley, dinette, two-drawer refrigerator, freezer, dishwasher, large pantry, a full-size convection microwave, and an additional full-size laundry center. To starboard is a king berth Captain’s cabin with an ensuite head, and to port a transverse twin berth crew cabin with an ensuite head. Forward of the crew area, through a watertight door, is an air-conditioned full-height engine room, with excellent access to the engines, generators, hydraulic and other systems that also includes a Headhunter waste treatment center.

Two stairways lead to the flybridge helm, equipped with state-of-the-art Garmin electronics, three electric Stidd seats, wing controls port and starboard, port and starboard L-shaped seating areas with Silestone tables, a large bar with three deck mounted stools, oversized grill, storage, refrigerator and an icemaker – all weather protected by the hardtop. The huge boat deck easily handles a tender with an overall length of almost 19’ feet, effortlessly maneuvered by the 2600lb davit.

The owners of JULIANNE, having previously increased the standard size of the stainless railings on their previous 70’ Outer Reef, chose to also invest in the installation of larger-than-standard sized stainless rails throughout the entire 90’ yacht, from 1 inch to 1 1/2 inches. This also included any horizontal raise and their vertical supports. In addition, the rail height was also increased by 5 inches over any previous build for added safety at sea.

HULL CONSTRUCTION

1. Hand laid-up FRP hull with PVC core sandwich construction above water line
2. Solid laminate, commensurate for hull size, made in female mold
3. Vinylester barrier lamination for osmosis protection
4. Simulated planked hull
5. Full length longitudinal engine stringers and athwartship stringers
6. Gel coated finish above waterline
7. Two (2) coats of black antifouling paint over five (5) coats of epoxy primer below waterline (Hauled out August 2024. All running gear inspected as well as the thrusters, stabilizer fins, and rudders. Hull below waterline was sanded, primed and Sea Hawk Biocop was reapplied. All running gear and rudders have Prop-Speed. Renewed all zinc anodes on the vessel)
8. Integrally molded rub rails with stainless steel capping
9. Full length keel extends below running gear
10. Stainless steel rudders and struts with two (2) Seatorque enclosed drive shaft systems (Inspected August 2024)
11. CE-approved stainless steel portlights
12. Boat construction from only 3 major molds
13. Divinycell PVC cored construction with cook gelcoat
14. All deck and hull area hardware attachments are finished with solid lamination – no coring
15. Bilge area finished smooth and coated with bright white epoxy paint
16. Windows with 3/8” tempered safety glass in salon and ½’ tempered safety glass in pilothouse
17. Quiet Roll™ integrated spray rail system
18. WheelHouse™ Technologies, Inc Marine Maintenance System
19. Flag Blue fashion hull stripe with gold accent

AFT DECK AREA

1. Aft deck with teak decking
2. Built-in 6' extended swim platform with teak decking (includes a 3' addition)
3. Stainless steel removable swim ladder on swim platform
4. Upgrades 2.5” 316 stainless steel removable safety rails on swim platform
5. Three (3) additional sockets on swim platform for rail storage
6. 20" bollards port and starboard
7. Stairway built-in to port and starboard side from swim platform to aft deck with FRP gate doors
8. Aft deck FRP bench seating with storage beneath
9. Five (5) Westminster Teak chairs with a Superyacht Finish with cushions
10. Sliding teak aft deck table with custom holly and wenge compass design and stainless-steel bases
11. Port side Silestone-topped bar cabinet with sink, refrigerator and a separate Vitrifrigo ice maker
12. FRP sliding door to salon with glass window top and bottom
13. FRP weather tight door on transom
14. Transom shower in recessed box with hot and cold-water supply
15. Fresh water wash down outlet
16. Shorepower inlets for 110v/220v 60hz
17. Two (2) Glendinning 100-amp cable masters, each with 100’ of cable, on transom
18. Glendinning electronic engine and bow/stern thruster controls via hand-held remote
19. Glendinning plug-in receptacle
20. Maxwell VC2500 capstans port and starboard
21. 316 Stainless-steel heavy-duty cleats secured to stainless steel backing plates inside bulwarks
22. Deck scuppers piped out through transom at boot stripe
23. 316 Stainless steel handrail to and from aft deck, upgraded from 1" to 1.5"
24. Built-in FRP stairs from aft deck to boat deck with hatch and 316 stainless steel rails, upgraded from 1" to 1.5"
25. Stairway has extra steps added, closer to home standards of building, which makes it less steep and safer
26. Pull-out trash can under the stairs
27. Two (2) corner hawse holes with rollers
28. Wing doors port and starboard
29. Two (2) LED working lights on aft deck overhang to light swim platform
30. Socket for a 50" Samsung TV (stowed in the salon settee)
31. Large towed tender whips and bulwark saddles (Installed January 2024)

SIDE DECKS AND PORTUGUESE BRIDGE

1. 316 stainless steel handrails alongside decks, upgraded from 1" to 1.5" and raised an additional 5" for added safety
2. Molded with beige non-skid surface
3. Marquipt 5-step boarding stairs with teak treads, with recessed storage on the starboard side deck
4. Life ring recessed into starboard house wall
5. Weather-tight doors opening into pilothouse port and starboard
6. House side fixed windows with tinted tempered glass
7. Five (5) 316 stainless steel hawser holes with stainless steel cleats per side recessed in bulwarks
8. Fuel fill fittings for tanks recessed into house side
9. 316 stainless steel overhead safety rails at side steps, upgraded from 1" to 1.5"
10. Portuguese bridge molded with beige non-skid surface
11. Locker doors in aft face of Portuguese bridge
12. 316 stainless steel handrails on top of Portuguese bridge, upgraded from 1" to 1.5" and raised an additional 5" for added safety
13. Glendinning plug-in receptacle
14. Hinged door through Portuguese bridge to foredeck
15. Three (3) stainless steel Exalto dual speed (intermittent) self-parking windshield wipers with wash down system
16. ½” Clear tempered glass in forward facing windshields
17. Windows are fixed with FRP recessed frames - no FRP trim around for easy removal and installation of glass

FORE DECK

1. Foredeck with beige non-skid surface
2. Seating with a sunbed extension
3. 316 Stainless steel CE-approved skylight/emergency hatch from the VIP stateroom below
4. 316 Stainless steel rail on bulwarks increasing in width going forward, upgraded from 1" to 1.5" and raised an additional 5" for added safety
5. 316 Stainless steel stanchions to support handrail, upgraded from 1" to 1.5"
6. Deck lockers forward either side of anchor platform finished in white epoxy paint
7. 316 Stainless steel anchor chute/roller at bow
8. 176lb Ultra anchor with swivel and 400' of 5/8" chain
9. Anchor snubber bridle
10. Maxwell VWC-4000 Hydraulic vertical windlass with foot switches and remote controls for dual stations
11. 20" bollards port and starboard
12. Saltwater wash down pump with outlet
13. Fresh water wash down with outlet
14. Deck drains plumbed to boot-stripe to prevent black streaks
15. Glendinning plug-in receptacle

FLYBRIDGE

1. Full-beam width deck with beige non-skid surface and ample storage space
2. 316 stainless steel safety rails, upgraded from 1" to 1.5" and raised an additional 5" for added safety
3. Venturi windscreen with 316 stainless steel rails, rails upgraded from 1" to 1.5"
4. Molded FRP steering console with engine controls
5. Electronics console
6. Glendinning electronic engine controls
7. 5” magnetic compass
8. Teleflex hydraulic power assist steering system (steering hoses inspected, filter changed and oil replaced in 2024)
9. 316 stainless steel destroyer steering wheel, upgraded from 1" to 1.5"
10. Three (3) low-back electric Stidd helm seats with Ultraleather and deluxe chrome bases
11. Carlile and Finch 200w Xenon high powered searchlight with dual station controls
12. Fire system repeater alarm
13. Two (2) L-shaped settees port and starboard
14. Two Silestone (2) tables with double pedestals
15. Five (5) Aquasignal navigation lights in accordance with appropriate collision regulations
16. Kahlenberg T-1 triple trumpet air horn with compressor
17. Kahlenberg for signal timer/horn control
18. Upgraded night vision
19. Socket for a 32" Samsung portable Smart TV (stowed in the salon settee)
20. FRP radar mast
21. Hard top over flybridge
22. 316 Stainless steel mast with bow and anchor lights
23. 316 Stainless steel sliding hatch and stairs starboard side down to pilothouse (handrails upgraded from 1" to 1.5")
24. Gate door to boat deck

BOAT DECK

1. Deck with beige non-skid surface
2. 316 stainless steel handrails, upgraded from 1" to 1.5" and raised an additional 5" for added safety
3. Life ring recessed to port
4. Cabinet behind starboard settee with a sink, Vitrifrigo ice maker and 30" SeaStar built-in gas BBQ grill
5. Cabinet with Silestone bar top to port with a Vitrifrigo fridge and storage underneath, and three fixed yellow marine-grade vinyl bar stools
6. 1200KGS/2600lb aluminum painted davit with 4-way hydraulic control with rotating base, luff, lift, pendant switch and a 13.7’ telescoping arm (2024 - davit inspected as was the cable - oil replaced in reservoir)
7. Five (5) triangle shade sails with adjustable stainless steel removable posts (post storage port and starboard)
8. Removable upgraded (from 1" to 1.5") 316 stainless steel ladder from boat deck to hardtop
9. Two (2) LED working lights on radar arch
10. Glendinning plug-in receptacle
11. Two (2) Ocean ISO 8-man life rafts mounted into port and starboard side railing (rafts service due May 2025)
12. 19' 525 Walker Bay fully equipped tender with 115 Evinrude ETEC motor
13. Two (2) SeaBobs with deck storage cradles and chargers
14. Custom extra-large sunbed at the end of the deck with gas struts for hatches and side storage lockers port and starboard

ENGINE ROOM AND MECHANICAL

1. Acoustically insulated stand-up engine room lined with Soundown sound and vibration absorbing material
2. Edura beige coin dot flooring
3. Twin Caterpillar C-18 Acert (1001 bhp) diesel engines with ZF transmissions and electronic instruments for dual stations (approximately 1770 hours - units were serviced and inspected at 1688 hrs)
4. Two (2) Seatorque enclosed drive shaft systems and two (2) Nibral propellers (Inspected and serviced by Seatorque, November 2022. Propellers retuned and balanced by Stuart Propellers, November 2022)
5. Stainless steel removable work benches over the engines
6. Fiberglass drip pans under engines
7. Blue strip LED lighting at the engine beds
8. Twin Northern Lights 38k (60hz) generators with sound shields (P: 1704 hrs, S: 1546 hrs - both units borescoped at the yard, had new injectors installed as well as all valve lashing adjusted. New oil pressure sensors installed)
9. Upgraded ABT Trac 55hp hydraulic bow and stern thrusters (substantial upgrade)
10. Upgraded ABT Trac 250 stabilizers with 9 sq. ft. fins (2024 - hoses inspected as was the actuators and fins. New Zincs on the fins. Oil reservoir filter replaced)
11. 25 gallon waste tank installed in 2022, with two 16 gallon fresh lube tanks
12. Northern Lights uplift water separator exhaust
13. Underwater exhaust system with bypass and FRP mufflers
14. Copper bonding system to all underwater fittings with zinc anodes
15. Rigid fresh water pipes and color-coded copper fuel lines
16. Stainless steel struts with bearings
17. Headhunter 24v DC and Mach-5 115v AC fresh water pumps with accumulator tanks
18. Two (2) 24v DC automatic shower sump systems with external pump
19. Accessible wiring raceway throughout
20. MarineAir chilled water air conditioning system (two 48,000 btu compressors and 12 air handlers - AC compressors were serviced in 2024 and both are in good shape)
21. Additional separate engine room air conditioning system
22. Back-up raw water cooling pump for the AC system
23. Two (2) raised sea chests
24. Ball-valve bronze seacocks on all through-hulls below waterline located in sea chests
25. Reverso oil change system for engines, generators and transmissions (fresh and waste oil tanks added Fall 2022 to the system)
26. Two (2) 100amp isolation transformers
27. Two (2) prop shaft brushes
28. 4 kw inverter/charger (24v DC to 115v AC 60Hz)
29. 4 kw inverter/charger (115v AC to 230v AC 60Hz)
30. Asea power converter 36k VA / 1/3ph input 1ph output, can convert from 100 amp 3-phase to 100 amp single-phase (serviced in the spring of 2024 - new fans, power modules were cleaned)
31. $63,000 in upgrades to shore power and electrical system, upgraded to 100 amp 3-phase power
32. Two (2) Racor 75/1000 max dual fuel filters with gauges for main engines
33. Two (2) Racor 75/1000 max single fuel filters for generators
34. Racor fuel polishing system
35. Fuel management system
36. Fireboy fire suppression system including both intake and outlet air shutdown system with aluminum louvers
37. Four (4) automatic bilge pumps 24v DC and emergency bilge suction on engine
38. Fire system and bilge high-water alarm system with warning panel
39. Fresh water hose bibb
40. AGM (Absorbed Glass Matt) batteries in FRP boxes:
41. Two (2) engine banks with two (2) 8D batteries for each bank
42. One (1) house bank with eight (8) 8D batteries with a total 1020 amp-hours (24VDC)
43. Two (2) generator banks with one (1) battery each
44. One (1) 24v and one (1) 12v battery charger
45. Two (2) battery isolators
46. Three (3) 20-gallon water heaters with heat exchangers
47. Grundfos 115v circulation pump for the hot water system
48. FCI Watermakers 1,800 gpd water maker (376 hours of operation - unit shows NO degradation of water quality or quantity)
49. Dock-Mate 1004 10 X 30" water softening system including a whole boat carbon filter system and a VH410 UV sterilizer
50. Headhunter X-Caliber (24v DC) back-up pump for fresh water
51. Headhunter MX waste treatment system ($68,000 upgrade - installed by Headhunter in the US - salt water pump replaced in August 2024)
52. Four (4) 24v DC blowers
53. 316 stainless steel safety rails around engines, upgraded from 1" to 1.5"
54. Work bench space
55. Two watertight bulkheads
56. Watertight aluminum engine room door with a sight window

Tankage

1. One (1) holding tank with a max capacity of 350 US gallons with two (2) macerator/discharge pumps. One (1) is wired and plumbed for backup redundancy
2. One (1) stainless steel water tank with a max capacity of 600 US gallons
3. Three (3) aluminum fuel tanks with a total capacity of 3,500 US gallons
4. All fuel tanks, water tank, and waste tank were cleaned August 2024
5. Fresh lube (2 16-gallon tanks)
6. Waste lube (1 25-gallon tank)
7. Lexan sight gauges on fuel tanks
8. Inspection and cleaning ports on all tanks
9. Fuel fills built into house sides in FRP cabinet

INTERIOR GENERAL

1. High gloss bullnose and details throughout
2. Beautiful high gloss teak star and monkey tail details throughout
3. Sound deadening Soundown throughout - in all the walls, all the floors and ceilings in every stateroom and all around the engine room, creating the quietest and most vibration-free Outer Reef built-to-date
4. LED lighting throughout entire vessel
5. Power shades in salon, galley, port guest, starboard guest and master staterooms
6. Custom finish cabin door hardware
7. Upgraded alternate hardware on interior cabinetry
8. Security safe

SALON

1. Sliding door entrance from aft deck
2. Entire length of the salon has an extra-thick layer of Soundown sound and vibration absorbing material, overlaid by an extra-thick pad and carpeting
3. Staircase with Bolon inlay leading to the crew area
4. Fixed windows in house sides with medium 3/8” tinted tempered safety glass
5. Teak valance over windows with LED rope lighting
6. Wall sconces
7. Reading lights
8. Vinyl headliner
9. Coffer ceiling detail in high gloss
10. Entertainment center cabinet starboard with additional storage cabinets
11. Custom-built mahjong dining table with four chairs, all with Superyacht high gloss finish
12. Custom-built sofa, side table, and two custom-made ottomans to port
13. Two custom chairs to starboard
14. Glass-front stemware/barware storage cabinet
15. Air conditioning control panel
16. Teak cabinetry and lockers
17. Carpeted floor
18. Teak wall paneling with satin finish

Galley

1. Open galley layout with island
2. An electric privacy partition wall (aft side has an underwater photograph by a Florida photographer, forward side with five star holly and wenge inlay design)
3. Opening window
4. Silestone countertops with a subway tile backsplash and a stainless steel under-mount Elkay sink
5. Drawer for soap and sponges in front of the sink
6. Teak wall paneling with satin finish
7. Teak flooring
8. GE Monogram 36” counter-depth side x side refrigerator
9. GE Monogram 24” dishwasher with stainless interior
10. GE Monogram 30” built-in microwave
11. GE Monogram 30” electric cooktop
12. GE Monogram 30” built-in oven
13. Echelon Wine Captain 15” wine cooler
14. Garbage disposal with switch
15. Two-bin garbage
16. Pull-out spice rack
17. Large floor-to-ceiling pantry with 6 pull-out bins
18. Custom-built emergency locker for two fire extinguishers and an emergency flashlight
19. Air conditioning control panel

DAY HEAD

1. Silestone countertop with sink
2. Custom raised decorative glass backsplash
3. Teak framed mirror with high gloss finish
4. Storage cabinet under sink
5. Wallcovering above chair rail with teak paneling below
6. Headhunter 24v electric white toilet with sanitary hose for all discharge plumbing
7. Ventilator blower
8. Teak flooring
9. Watertight exterior door

PILOTHOUSE

1. U-shaped settee on raised platform
2. Granite table with 316 stainless steel pedestals
3. LED red and white bridge lights
4. Reading lights
5. Two (2) low-back electric Stidd helm seats with Ultraleather and deluxe chrome bases
6. Binocular box
7. Custom hand-crafted 1.5" teak Outer Reef steering wheel at pilothouse helm
8. Burl console face
9. Teleflex power steering system
10. Engine display screens
11. Overhead electronics console
12. Wiring routes to facilitate equipment installation
13. Main electrical distribution panels with gauges and circuit breakers for AC and DC
14. Outer Reef alarm and advisory panel
15. Headhunter sewage treatment system control and monitoring panel
16. Transom doors on AC, DC and advisory panels
17. AC system remote monitor panel
18. Glendinning electronic engine controls with backup gear and throttle with synchronizer
19. 5” magnetic compass
20. Vinyl headliner
21. Control for bow and stern thruster
22. Air conditioning control panel
23. Generator digital control panel
24. 24v DC to 12v DC converter
25. Windlass up/down switch and control circuit breaker
26. Bilge pump control on advisory panel